Grades

1. Typical Properties

Select the suitable grades of PELESTAT by referring to the table below.

PELESTAT
NC6321

PELESTAT
NC7530

PELESTAT
300

PELESTAT
230

Appearance

Pale yellow pellet

Pale yellow
pellet

Melting point

°C

202

176

135

160

Melt flow rate^*1

g(10min)

Refractive index

1.51

1.53

1.49

1.50

Thermal degradation temp ^*2

°C

285

280

240

250

Surface resistivity^*3

1*10⁹

2*10⁹

1*10⁸

5*10⁷

Necessary amount^*4

wt%

10-15

12-17

5-15

Adapted thermoplastic resins

Styrene plastics such as ABS and HIPS, polyester resin such as PBT, PC/ABS alloy and nylon

Styrene plastics such as MS resin

Polypropylene series

Polyethylene and Polypropylene sheet

*1:	Measured according to the method described in ASTM D 1238 (PELESTAT NC6321: 215°C, 21.18 N, PELESTAT NC7530, PELESTAT 300 and PELESTAT 230: 190°C , 21.18 N)
*2:	Measured using a TG-DTA apparatus in the air
*3:	PELESTAT itself was molded using an injection molding machine into test pieces, and then the surface resistivity of them was measured using an ultra-megohmmeter at 23°C under 50 % R.H.
*4:	Amount necessary to achieve surface resistivity between 10¹¹ and 10¹²

2. Relation between Amount of PELESTAT Added and Surface Resistivity

Amount of PELESTAT NC6321 Added to ABS Resin and Surface Resistivity

Amount of PELESTAT NC7530 Added to MS Resin and Surface Resistivity

Amount of PELESTAT 300 Added to PP and Surface Resistivity

Amount of PELESTAT 230 Added to LDPE Resin and Surface Resistivity

3. Influence of PELESTAT on Physical Properties of Resin

PELESTAT does not deplete the physical properties of predetermined resins, because this product excels in compatibility.

Resin

ABS Resin

MS Resin

LDPE Resin

PELESTAT

NC6321

NC7530

300

230

Amount of PELESTAT Added to Resin

wt%

Surface resistivity^*1

2*10¹¹

>10¹⁶

8*10¹¹

>10¹⁶

2*10¹²

>10¹⁶

3*10¹¹

>10¹⁶

Melt flow rate^*2

g(10min)

Melt flow rate^*3

MPa

Fracture elongation^*4

300

280

600

580

Flexual modulus^*5

MPa

2,200

2,300

2,700

2,900

1,200

Izod impact strength
(notched)^*6

J/m

140

150

Du Pont impact strength ^*7

Deflection temp. under load
(1.82 MPa)^*8

°C

Total light transmittance ^*9

86^*10

Haze^*9

35^*10

34^*10

*1:	ASTM D 257
*2:	ASTM D 1238 (ABS resin: 220°C, 98.07 N, MS resin: 230°C, 98.07 N, PP: 230°C, 21.18 N, LDPE: 190°C, 21.18N)
*3:	ASTM D 638
*4:	ASTM D 638
*5:	ASTM D 790
*6:	ASTM D 256 (notched)
*7:	JIS K 5400
*8:	ASTM D 648 (ABS resin and MS resin: 1.82 MPa, PP: 0.45 MPa)
*9:	JIS K 7105 (thickness of test pieces: 2 mm)
*10:	JIS K 7105 (thickness of test pieces: 200 µm)